Fluke                                                       MET/CAL Procedure
=============================================================================
INSTRUMENT:            Goerz SE120: (1 year) CAL VER /5500
INSTRUMENT:            Goerz SE124: (1 year) CAL VER /5500
DATE:                  04-Sep-97
AUTHOR:                Fluke Corporation
REVISION:              $Revision: 1.4 $
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       6
NUMBER OF LINES:       85
CONFIGURATION:         Fluke 5500A
=============================================================================
#
# Compatibility:
#   5500/CAL 4.0 or MET/CAL 4.0 or later.
#
# Subprocedures:
#   Sub Goerz SE120/SE124 (1 year) CAL VER /5500
#
# Required Files:
#   None
#
# System Specifications:
#   TUR calculation is based on specification interval of the accuracy file.
#   The default 5500A accuracy file contains 90 day specs.
#
# Fluke makes no warranty, expressed or implied, as to the fitness
# or suitability of this procedure in the customer's application.
#
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-                        P                            F        V
  1.002  ASK+           K                              X
  1.003  HEAD         PRELIMINARY INSTRUCTIONS
  1.004  DISP         Connect UUT to AC power and turn unit ON.
  1.004  DISP
  1.004  DISP         Warm-up time: 30min - REQUIRED
  1.004  DISP         Temperature: 23 +/-2 degC
  1.004  DISP         Humidity: 55 +/-10%
  1.005  DISP         [32]                WARNING
  1.005  DISP         HIGH VOLTAGE is used or exposed during the performance
  1.005  DISP         of this calibration.
  1.006  MEM2         =Channel 1
  1.007  CALL         Sub Goerz SE120/SE124 (1 year) CAL VER /5500
  1.008  JMP          2.001
  1.009  EVAL   Dummy
  2.001  MEM2         =Channel 2
  2.002  CALL         Sub Goerz SE120/SE124 (1 year) CAL VER /5500
  2.003  JMP          3.001
  2.004  EVAL   Dummy
  3.001  MEM2         =Channel 3
  3.002  CALL         Sub Goerz SE120/SE124 (1 year) CAL VER /5500
  3.003  HEAD         {DISTANCE BETWEEN RECORDING PENS}
  3.004  DISP         Use the ZERO knob on the measuring units to shift the
  3.004  DISP         trace to the right-hand & left-hand stops. Repeat this
  3.004  DISP         process on each channel.
  3.005  MESS         Refering to the above traces:
  3.005  MESS
  3.005  MESS         The distance between recorded traces between channels
  3.005  MESS         must be 2.5mm +/-.2mm.
  3.005  MESS
  3.005  MESS         The recording pens must not obstruct each other.
  3.005  MESS
  3.006  EVAL   Are {the recording pens distances correct}?
  4.001  HEAD         {PEN SYNCH VERIFICATION}
  4.002  DISP         Connect the 5500A to the UUT as follows:
  4.002  DISP         [32] 5500A NORMAL HI to Channel 1, 2, and 3 INPUT HI
  4.002  DISP         [32] 5500A NORMAL LO to Channel 1, 2, and 3 INPUT LO
  4.003  5500         0V                                                S  2W
  4.004  DISP         Set the RANGE switch on all channels to 10V.
  4.005  DISP         Set all the pens to 50% using the ZERO control.
  4.005  DISP         Set the PAPER FEED to 60cm/min.
  4.005  DISP         Set the CHART FEED button to ON.
  4.006  5500         4V                           0.1H           SI    S  2W
  4.007  MESS         With the PEN SYNCH OFF verify that the channel traces
  4.007  MESS         are separated on the chart by approx. 2.5mm.
  4.007  MESS
  4.008  EVAL   Are {the traces separated by approx 2.5mm w/PEN SYNCH OFF}?
  5.001  DISP         Set the PEN SYNCH to ON.
  5.002  MESS         With the pen synch ON, channels 2&3 are stored
  5.002  MESS         temporarily and output with a time delay.  The delay
  5.002  MESS         depends on the chart speed and channel number.
  5.002  MESS
  5.003  EVAL   Are {the traces on top of each other w/PEN SYNCH ON}?
  6.001  DISP         Set the CHART FEED button to OFF.
  6.002  END